The table below details the key dimensions and kit contents of the 7 purchase options.
KIT CONTENTS
| Multi Pro 6,8,10mm |
Professional 6mm |
Professional 8mm |
Professional 8mm Long |
Professional 10mm |
Craftsmen 8mm |
Jobber 6mm |
Jobber 8mm |
|
| 225mm Long Bar | 1 | 1 | ||||||
| 116mm Standard Bar | 1 | 1 | ||||||
| 128mm Standard Bar | 1 | 1 | ||||||
| 128mm Standard Bar | 1 | 1 | ||||||
| 80mm Bar | 1 | 1 | 1 | |||||
| 6mm drill stop | 1 | 1 | ||||||
| 8mm drill stop | 1 | 1 | 1 | 1 | ||||
| 10mm drill stop | 1 | 1 | ||||||
| 6mm doweling drill | 1 | 1 | 1 | |||||
| 8mm doweling drill | 1 | 1 | 1 | 1 | 1 | |||
| 10mm doweling drill | 1 | 1 | ||||||
| Allen key | 1 | 1 | 1 | 1 | 1 | 1 | ||
| End stop Assembly | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Finger spacer assembly | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| 1.0mm Finger | 14 | 14 | 14 | 14 | 14 | 14 | 6 | 6 |
| 1.5 Finger | ||||||||
| 2.0mm Finger | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
KEY MEASUREMENTS
| 6mm Standard Bar |
8mm Standard Bar |
10mm Standard Bar |
8mm Long Bar |
6mm Jobber Bar |
8mm Jobber Bar |
|
| Bar Width mm | 12 | 16 | 16 | 16 | 12 | 16 |
| Bar Depth mm | 20 | 20 | 20 | 20 | 20 | 20 |
| Bar Length mm | 116 | 128 | 128 | 225 | 80 | 80 |
| CSK Screw Mount Holes | 3 | 3 | 5 | 5 | 2 | 2 |
| 6mm end drilled & tapped % | Y | Y | Y | Y | ||
| 6mm side plain drilled | 4 | 3 | 5 | 5 | 2 | 2 |
| Top side dowel holes | 8 | 7 | 6 | 10 | 4 | 4 |
| As Supplied Max Dowel Reach * | 17 | 16 | 16 | 16 | 17 | 16 |
| As Supplied Min Dowel Reach # | 6 | 7 | 8 | 7 | 6 | 7 |
| Hole count & spacing | 7 on 16mm centres and 3 on 8mm centres ^ |
7 on 16mm centres | 6 on 20mm centres | 7 on 32mm and 6 on 16mm centres ^ |
4 on 16mm centres | 4 on 16mm centres |
* The approximate maximum distance in from the reference face using a single 1mm spacer tab and the 50mm set screw supplied as standard. For example a 10mm jig as supplied will centrally place dowels in stock of about 32mm (1 1/4 inches).
Note: To simply increase this use a longer set screw and additional spacer tabs. For extreme reach use 6mm booker (threaded ) rod.
# The approximate minimum distance in from the reference face using any spacer tab.
% All bars have one end drilled and tapped for the end stop assembly. All bars other than Jobbers have the other end drilled and tapped to allow for end to end bar arrays and other atttachment options.
^ These bars have two rows of equally spaced dowel holes interleaved on the one bar